WS License Manager 1.00 serial key or number

1.1      System Management

Default Settings

AC：No default IP address.

AP：Default IP address is 192.168.110.1(or 192.168.1.1), and both console & telnet password are "admin", default enable password is "apdebug"

Following wall AP have different default settings

AP120-W

In Fit mode, IP address of both LAN port and Uplink port IP are 192.168.110.1/24

In Fat mode, IP address of LAN port is 192.168.111.1/24; IP address of Uplink port is 192.168.110.1/24

AP110-W

IP address of Rear panel is 192.168.110.1/24

IP address of Front panel is 192.168.111.1/24

1.1.1     Console Management

Connect cables as below diagram

Cables

console cable, USB to RS232 cable 

Putty

Open software Putty, set baud rate to 9600

1.1.2     Telnet Management

I. Network Topology

II. Configuration Steps

Configuring Telnet& enable password on AC

Ruijie>enable

Ruijie#configure terminal

Ruijie(config)#interface vlan 1 

Ruijie(config-if-vlan 1)#ip address 192.168.1.1 255.255.255.0

Ruijie(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.2

Ruijie(config)#line vty 0 4

Ruijie(config-line)#password ruijie

Ruijie(config-line)#login

Ruijie(config)#enable password ruijie

Configuring Telnet & Enable password on AP

Console connect to device and set passwords, default ap-mode is fit.

User Access Verification

Password:                                              default password is "ruijie"

Ruijie>

Ruijie>enable

Password:                                              default password is "apdebug"

Ruijie#configure terminal

Ruijie(config)#interface bvi 1

Ruijie(config-if-bvi 1)#ip address 192.168.1.1 255.255.255.0

Ruijie(config-if-bvi 1)#interface gigabitEthernet 0/1

Ruijie(config-if-GigabitEthernet 0/1)#encapsulation dot1Q 1

%Warning: Remove all IP address.

Ruijie(config-if-GigabitEthernet 0/1)#exit

Ruijie(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.2 

Ruijie(config)#line vty 0 4

Ruijie(config-line)#password ruijie

Ruijie(config-line)#login

Ruijie(config)#enable password ruijie

Note: when ap-mode change from fit to fat, the default password changes as follow:

User Access Verification

Password:                                              default password is "admin"

Ruijie>

Ruijie>enable

Password:                                              no default password

Ruijie#configure terminal

III. Verification

Save configuration

Ruijie(config)#end

Ruijie#write

Note:

windows7&8 telent client function is not enabled by default, you need to enable the telnet functionality.

Taking Windows 7 as an example:

Control panel - procedures and functions - to open or close the windows function - check the telnet client - select "to determine"

1.1.3     SSH Management

I. Network Topology

II. Configuration Steps

Configuring SSH on AC

Ruijie>enable

Password:

Ruijie#configure terminal         

Ruijie(config)#enable service ssh-server    

Ruijie(config)#crypto key generate dsa       

Choose the size of the key modulus in the range of 360 to 2048 for your

Signature Keys. Choosing a key modulus greater than 512 may take

a few minutes.

How many bits in the modulus [512]:                

% Generating 512 bit DSA keys. ..[ok]

Ruijie(config)#interface vlan 1  

Ruijie(config-if-VLAN 1)#ip address 192.168.1.1 255.255.255.0

Ruijie(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.2

Ruijie(config)#enable password ruijie

Method 1：Login with password

Ruijie(config)#line vty 0 4

Ruijie(config-line)#password ruijie      

Ruijie(config-line)#login                          

Ruijie(config-line)#end                                                  

Ruijie#write   

Building configuration...

[OK]

Ruijie#                                                              

Method 2：Login with username & password

Ruijie(config)#line vty 0 4       

Ruijie(config-line)#login local                                

Ruijie(config-line)#exit

Ruijie(config)#username admin password ruijie        

Ruijie(config)#end    

Ruijie#write      

Building configuration...

[OK]

Ruijie#        

III. Verification

Open Putty, choose Connection type "SSH", input IP address.                                                 

    To display SSH service status, execute following commands

1.1.4     Web Management

I. Network Topology

II. Configuration Steps

Configuring WEB GUI on AC

Ruijie#configure terminal       

Ruijie(config)#enable service web-server 

Ruijie(config)#vlan 1   

Ruijie(config-vlan)#interface vlan 1      

Ruijie(config-if-VLAN 1)#ip address 192.168.1.1 255.255.255.0

Ruijie(config-if-VLAN 1)#exit

Ruijie(config)#webmaster level ?

  <0-2>  Web auth privilege level (0 is the highest level)

Ruijie(config)#webmaster level 0 username ruijie password ruijie

Ruijie(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.254

Note:

1.     AM5528 does not support web management.

2.     Only user “admin” and “ruijie” could be created on cli page, for other account, If you have the web management requirements, please create it on web interface, relative err prompt are shown as follow:

III. Verification

Visit web GUI at http://192.168.1.1, it is recommended that access WEB GUI with IE 8.0 and above version in compatible mode.

1.1.5     Forget IP Address of Wall AP

If administrator forgot IP address of Wall-AP, and do not want to recover factory setting, follow below steps:

1. Power on AP, and connect AP as below diagram:

2. Open packet capture tool, here take Wireshark as example:

3.     Check ARP packets, and 192.168.51.54 is correct IP

4.     Try to telnet AP

5.     If above method doesn't work, suggest to restore factory default.

1.2      Firmware Upgrade

1.2.1 Upgrade for RGOS 11.x

1.2.1.1    Upgrade AC & Fit AP (for 11.X)

I. Network Topology

II. Requirements

1.     Visit official website at www.ruijienetworks.com to request firmware.

2.     Run TFTP Server, and put AP&AC firmware in the same folder. Here take Ruijie TFTPServer as example.

 TFTP Server should be able to communicate with AC.

3. AC has built CAPWAP tunnel with APs

4. Read Release Note carefully, pay attention to the "upgrade file"

5. DO NOT restart or POWER OFF AC&AP during upgrades.

6. Login AC CLI via console, telnet or SSH.

III. Configuration Steps

Upgrading AC

Attention：In hot-backup scenario, please remove all networks cables on ACs in case of synchronization issue caused by inconsistent firmware.

1.     Display current firmware version and backup relative configuration files.

Ruijie# copy flash:config.text tftp://192.168.1.100/config.text --->backup the configuration files of AC to TFTP Server.

Ruijie# copy flash:ap-config.text tftp://192.168.1.100/ap-config.text ---> backup the configuration of AP to TFTP Server.

Ruijie#show version detail

System description     : Ruijie 10G Wireless Switch(WS6008) By Ruijie Networks.

System uptime          : 0:02:15:24

System hardware version: 1.0

System software version: AC_RGOS 11.1(5)B80P3, Release(04131820)

System patch number    : NA

System software number : M20361001182017

System serial number   : 1234942570002

System boot version    : 2.0.19.97cfa98(161210)

System core version    : 2.6.32.355270930a6bde

System cpu partition   : 4-11

2.     Transfer new firmware to AC, execute below commands:

Ruijie#upgrade download tftp://192.168.1.100/rgos.bin

III. Verification

After reloading, execute command "show version" to verify firmware version.

Ruijie#show version detail

System description     : Ruijie 10G Wireless Switch(WS6008) By Ruijie Networks.

System uptime          : 0:02:15:24

System hardware version: 1.0

System software version: AC_RGOS 11.1(5)B80P3, Release(04131820)

System patch number    : NA

System software number : M20361001182017

System serial number   : 1234942570002

System boot version    : 2.0.19.97cfa98(161210)

System core version    : 2.6.32.355270930a6bde

System cpu partition   : 4-11

Upgrading Fit APs
Attention：Generally, the fit ap and ac can work normally only when the versions of them are consistent

1.     Display current ap firmware version on AC, execute commands "show version all"

Ruijie#show version detail

System description     : Ruijie Indoor AP330-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 1969-12-31 23:59:59

System uptime: 0:00:01:09

System hardware version: 1.10    ------>hardware version

System software version: AP_RGOS 11.1(5)B3, Release(02160403)------>software version

System patch number    : NA

System software number : M03112104042015

System serial number: G1GDB16019485

System boot version    : 1.1.1.6822c2a(140920)

System core version    : 2.6.32.ab930e7d22374b   

2.     To transfer AP new firmware to AC,  execute below commands:

Ruijie#copy tftp://192.168.1.100/330.bin flash:330.bin

Press Ctrl+C to quit

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Copy success

3.     To configure ap-serial,  execute below commands:

Ruijie(config)#ac-controller

Ruijie(config-ac)#active-bin-file flash:330.bin

Ruijie(config-ac)#ap-image auto upgrade

4.     After AP reloading, APs will establish CAPWAP tunnel with AC.

III. Verification

1.     Display AP upgrading progress,  execute commands "show ap-config updating-list"

Ruijie#show ap-config updating-list

AP NAME                                  AP PID          File Tx                  Time               AP Reset Ready

----------------------           ---------------     --------               ------------     -----------

AP330-I                                  AP330-I          20 %                 00:00:06               N

2.     Display current ap firmware version on AC,  execute commands "show version all"

Ruijie>show version     

System description     : Ruijie Indoor AP330-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 1970-01-01 00:00:01

System uptime: 0:00:01:52

System hardware version: 1.10

System software version: AP_RGOS 11.1(5)B5, Release(02182520)

System patch number    : NA

System serial number: G1GDB16019485

System boot version    : 1.1.1

1.2.1.2    Upgrade Fat AP (for 11.X)

I. Network Topology

II. Requirements

1.     Visit official website at www.ruijienetworks.com to request firmware.

2.     Run TFTP Server, and put AP firmware in the same folder. Here take Ruijie TFTPServer as example.

TFTP Server should be able to communicate with AP.

3. Read Release Note carefully, pay attention to the "upgrade file"

4. DO NOT restart or POWER OFF AP during upgrades.

5. Login AP CLI via console, telnet or SSH.

Attention: Wall APs, like AP130 (W2) & AP130L, do not have console port. See Device Management -->Conventions to learn the default IP address.

III. Configuration Steps

Upgrading FAT APs

1.     Backup configuration files to TFTP Server, and display current firmware version

Ruijie#copy flash:config.text tftp://192.168.1.100/config.text --->backup configuration files of AP to TFTP Server

Ruijie#show version detail  ---> check version

System description     : Ruijie Indoor AP330-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 1969-12-31 23:59:59

System uptime: 0:00:01:09

System hardware version: 1.10

System software version: AP_RGOS 11.1(5)B3, Release(02160403)

System patch number    : NA

System software number : M03112104042015

System serial number   : G1GDB16019485

System boot version    : 1.1.1.6822c2a(140920)

System core version    : 2.6.32.ab930e7d22374b

2.     Display current ap mode

AP320#show ap-mode

current mode: fat

AP320#

3.     Transfer new firmware to AP,  execute below commands:

Ruijie#upgrade download tftp://192.168.1.100/330-b5.bin

Upgrade the device must be auto-reset after finish, are you sure upgrading now?[Y/n]y

Running this command may take some time, please wait.

Please wait for a moment......

Press Ctrl+C to quit

!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!.!!!

Begin to upgrade the install package 330-b5.bin...   --->reload automatically

*Jan  1 00:03:52: %7: Upgrade processing is 10%

Uncompress file 330-b5.bin. .......

IV. Verification

After reloading,  execute command "show version"  to verify firmware version.

Ruijie#show version  detail

System description     : Ruijie Indoor AP330-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 1970-01-01 00:00:01

System uptime: 0:00:01:09

System hardware version: 1.10

System software version: AP_RGOS 11.1(5)B5, Release(02182520)

System patch number    : NA

System software number : M20085306252015

System serial number   : G1GDB16019485

System boot version    : 1.1.1.6822c2a(140920)

System core version    : 2.6.32.720c78d1a03d63

1.2.2     Upgrade from RGOS 10.x to 11.x

1.2.2.1     Upgrade AC & Fit AP from 10.X to 11.X

I. Network Topology

II. Requirements

1.     Visit official website at www.ruijienetworks.com to request firmware..

2.     Run TFTP Server, and put AP&AC firmware in the same folder. Here take Ruijie TFTPServer as example.

 TFTP Server should be able to communicate with AC.

3. AC has built CAPWAP tunnel with APs

4. Read Release Note carefully, pay attention to the "upgrade file"

5. DO NOT restart or POWER OFF AC&AP during upgrades.

6. Login AC CLI via console, telnet or SSH.

III. Configuration Steps

Upgrading AC

Attention：In hot-backup scenario, please remove all networks cables on ACs in case of synchronization issue caused by inconsistent firmware.

1.     Display current firmware version and backup relative configuration files.

Ruijie#copy flash:config.text tftp://172.18.158.204/config.text --->backup the configuration files of AC to TFTP Server.

Ruijie#copy flash:ap-config.text tftp://172.18.158.204/ap-config.text ---> backup the configuration of AP to TFTP Server.

2.     Transfer new firmware to AC,  execute below commands:

Ruijie#copy tftp://172.18.158.204/AC_RGOS10.x_TO_11.x(Mid)_G1C5-01_02172111.bin flash:rgos.bin

After reloading, execute command "show version" to verify firmware

3.     Because the configuration files will lost when upgrade to mid version, need to import the config.text, and test the connection between AC and terminal, then Downgrade AC to target version 11.x

Ruijie#upgrade download tftp://192.168.1.100/AC_RGOS11.1(5)B8_G1C5-01_03151003_install.bin

IV. Verification

       After reloading, execute command "show version" to verify firmware version

Upgrading Fit APs

1.     Transfer 11.x and mid version of AP to AC,  execute below commands:

Ruijie#copy tftp://172.18.158.204/AP_RGOS10.x_TO_11.x(Mid)_S2C3-01_02201910.bin flash:ap530-mid.bin

Ruijie#copy tftp://172.18.158.204/AP_RGOS11.1(5)B8_S2C3-01_03151007_install.bin flash:ap530.bin

2.     To configure ap-serial,  execute below commands:

Ruijie(config)#ac-controller

Ruijie(config-ac)#active-bin-file ap530-mid.bin   rgos10

Ruijie(config-ac)#active-bin-file ap530.bin

Ruijie(config-ac)#ap-serial ap530 AP530-I hw-ver 1.x 

Ruijie(config-ac)#ap-image ap530-mid.bin ap530

Ruijie(config-ac)#ap-image ap530.bin ap530

IV. Verification

1.     After reloading, execute command "show version" to verify firmware version

2.     After AP reloading, APs will build CAPWAP tunnel with AC.

1.2.2.2    Upgrade Fat AP from 10.X to 11.X

I. Network Topology

II. Requirements

1.     Visit official website at www.ruijienetworks.com to request firmware.

2.     Run TFTP Server, and put AP firmware in the same folder. Here take Ruijie TFTPServer as example.

TFTP Server should be able to communicate with AP.

3. Read Release Note carefully, pay attention to the "upgrade file"

4. DO NOT restart or POWER OFF AP during upgrades.

5. Login AP CLI via console, telnet or SSH.

Attention: Upgrade from 10.X to 11.X, configuration will lost, backup the configuration before downgrading; need to downgrade to mid version first.

III. Configuration Steps

Upgrading FAT APs

1.     Backup configuration files to TFTP Server, and display current firmware version

Ruijie#copy flash:config.text tftp://192.168.111.2/config.text --->backup configuration files of AP to TFTP Server

2.     Display current ap mode

Ruijie#show ap-mode

current mode: fat

3.     Transfer new firmware to AP,  execute below commands:

Ruijie#copy tftp://192.168.111.2/AP_RGOS10.x_TO_11.x(Mid)_S2C3-01_02201910.bin flash:rgos.bin

Upgrade the device must be auto-reset after finish, are you sure upgrading now?[Y/n]y

Running this command may take some time, please wait.

Please wait for a moment......

Press Ctrl+C to quit

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Verification

4.     downgrade to target version 11.x

Ruijie# upgrade download tftp://192.168.111.2/AP_RGOS11.1(5)B8_S2C3-01_03151007_install.bin

5.      reload and verification

You may need a serial number and product key to activate some Autodesk software. 

Note: If you are on subscription, you may no longer need to enter a serial number or product key; you just need to sign in. Serial numbers are never required for launching products with network licenses.

Physical Media

Serial Numbers do not appear on software packaging for Autodesk software versions 2014 and newer. Serial numbers for these versions are emailed to you after you place an order or can be found in Autodesk Account.

If you have physical media (a DVD or USB key) for a 2013 or earlier product, your serial number and product key will be printed on the label of the product packaging.

 
Example of label from 2011 version. Format is similar for 2010 - 2013 product releases.

Return to Top

Older product keys

If you can't find the product key for older versions of Autodesk software (2013 and later), you may be able to find it in a text file in the installation folder.

To determine if your product key is available in your installation folder:

1. Using your installation media, (USB key, DVD, download folder, etc.) navigate to the folder that contains the setup.exe file for your Autodesk product.
2. In that folder, look for a file named MID.txt, MID01.txt, MID02.txt or some variation on that name.
3. Open this file in Notepad and verify that the product name is correct.
4. The first five characters of the part number should also be the product key for that product.

Example:

MID: Autodesk_Design_Suite_Ultimate_2012_64bit_SWL_ENU_C009_EXE1
Product Name: Autodesk Design Suite Ultimate 2012
Platform: Windows XP/Vista/Win7
Media: ESD
Part Number: 769D1-05Y001-P503E, 769D1-05Y001-P504E

Return to Top

Features: Generate serial keys using custom number of columns and characters per column. Serial keys can contain uppercase and/or lowercase charactes and/or numbers. Generate up to 2 million serial keys in one turn (1 million with 32 bit version of SKG). Export serial keys to CSV, TXT documents. Import serial keys from CSV, TXT documents. Export serial keys to MySQL and MS SQL databases (SQL Query generator). Export serial keys to encrypted registration files (SHA-512). Update encrypted registration files (add new serial keys, delete or validate existing serial keys). Source code generator for encrypted registration files supporting C#.NET, Visual Basic .NET, C++ Builder, Delphi and Java applications. INNO and NSIS scripts are also supported! TRegistrationFile and TMSSQLRegistration components for Delphi & C++ Builder. Validate, add and delete serial keys from MS SQL server. Documentation and example projects for VB .NET, C# .NET, C++ Builder, Delphi, Java INNO and NSIS. Lifetime free upgrades.