Snag-It 4.3.1 serial key or number

The Yield Management Company

Archer Product Family
Software Version

Installation Manual

PN Revision AA

October 29, KLA-Tencor Confidential Optical Metrology

Copyright © by KLA-Tencor. All rights reserved worldwide. No part of this
publication may be reproduced, modified, transmitted, transcribed, stored in retrieval
system, or translated into any human or computer language, in any form or by any
means, electronic, mechanical, magnetic, chemical, manual, or otherwise, without
the express written permission of KLA-Tencor, One Technology Drive, Milpitas,
California
KLA-Tencor provides this documentation without warranty in any form, either
expressed or implied.
KLA-Tencor may revise this document at any time without notice.
This document may contain proprietary information and shall be respected as a
proprietary document with permission for review and usage given only to the rightful
owner of the equipment to which this document is associated.
This document was designed, produced and published by the Optical Metrology
Division, KLA-Tencor Corporation.

Printed in Migdal Ha’Emek, Israel
October 29,

"We are committed to assisting our customers in obtaining maximum value from
KLA-Tencor products by providing excellent support at exceptional value."

KLA-Tencor PN
Revision AA

Helpful Intranet sites:
WSO Optical Metrology site: manicapital.com
Optical Metrology Software Group site:
manicapital.com
Use this site to check for the latest software releases.
Optical Metrology User Documentation site:
manicapital.com
Use this site to check for the latest documents issued by OMD.

Table of Contents

Table of Contents

Table of Contents i

Preface ii

1. Introduction

Site Prerequisites 1

Deliverables 2

Installation Team Resources 2

Reference Documentation 2

2. Installation Procedure

Upgrading RDM 4

Before You Begin 4

Installation 4

System Backup 5
System Backup to Drive F 5

System Backup to DAT Tape 6

Uninstalling Software Version Security Module 7
Archer Software Installation 9
Enabling Licenses
3. Verifying the Correct Software Version
4. Upgrading KLASS Station Software
Prerequisites
Upgrade Procedure
Registering the MPX License

Verifying Correct Installation
Verifying the Installation on the KLASS Computer

Verifying Installation on the Archer System Computer
5. Configuring SnagIt to Use Tool Thermal Printer
6. Configuring the Tool for FA

PN KLA-Tencor Confidential i

Preface Preface
ii
Document Purpose

This Installation Manual is intended for KLA-Tencor CSEs. The manual
provides all the information required for:

♦ Upgrading Archer system software from version or , to
software version

♦ Reinstalling Archer system software version

NOTE

The notation software version , in this document stands for software
version with or without a service pack (1, 2,3, or 4).

Trademarks

KLA-Tencor® is a registered trademark of the KLA-Tencor Corporation.
Archer™, RDM™, KLASS™, Archer Analyzer™, AIM™ & MPX™ are trademarks
of the KLA-Tencor Corporation.
All other brand and product names may be trademarks of their respective
companies.

IMPORTANT

This document is applicable for all Archer Product Family systems.
This document includes examples (e.g., screenshots) taken from the
Archer

Glossary Advanced Imaging Metrology
Adaptive Noise Reduction Algorithm
AIM Box in Box, Bar in Bar or Frame in Frame Overlay target
ANRA Bright Field Critical Dimension
BIB Critical Dimension
BFCD Coherence Probe Metrology algorithm
CD Customer Support Engineer
CPM Dataset Identification Section in the LIED file (the section
CSE that contains the description and identification data of the
DIS dataset file)
Equipment Constant
EC Equipment Front End Module (Wafer Handler)
EFEM Front Interface Mechanical Standard
FIMS Front Opening Universal Pod (closed wafer carrier that
FOUP maintains a dust-free atmosphere even outside a clean
room environment). Used on FIMS and SMIF EFEMs.

KLA-Tencor Confidential Archer Installation

Preface

FFU Filter Fan Unit
FOV Field of View
GEM Generic Model for Communication and Control of SEMI
Equipment
IDA Image Display Area
IDM Integrated Diagnostic and Monitoring
KLASS KLA Stepper Setup
LIED Litho-Information Exchange Dataset
LLC Lower Left Corner
LRC
MCDB Lower Right Corner
ML
MPX Machine Configuration Database
MTS Multi Layer
Monitor Photo eXcursion
OEE Metrology Tool Section in the LIED file (the section in which
OVL the Archer Tool writes the measurement results).
PM Overall Equipment Efficiency
PPT Overlay (refers to both BIB and AIM)
PZT Preventive Maintenance
RDM Ported Program Treatment
RPL Piezoelectric Transducer
SFO Recipe Data Manager
SMIF RS1 Programming Language
SP System Focus Offset
SRN Standard Mechanical Interface
SW Service Pack
TD Software Release Note
TIS Software
Target Dimension (related to the MPX application)
TTR Tool Induced Shift – overlay measurement contributed by
UDS the overlay tool.
UI Time to Results
ULC User Defined Section in the LIED file
URC User Interface; the Windows NT interface on the system.
VID
Upper Left Corner
Upper Right Corner

Variable identification

PN KLA-Tencor Confidential iii



Section 1: Introduction Site Prerequisites

1. Introduction

This section lists all the prerequisites required for installing software
version
♦ Site Prerequisites: Items, resources and information, supplied by the

customer.
♦ Deliverables: Items supplied by KLA-Tencor.
♦ Installation Team Resources: Items, resources and information the

installation team should bring with them.

IMPORTANT

Before starting the installation procedure, read section 1 carefully.

CAUTION
If you are using an RDM Server, and the installed RDM software version is
lower than , you must first upgrade RDM Server to software version

Site Prerequisites

Verify that the following items are present on site:
♦ Archer system with software version or installed on the tool.
♦ GB of free space available on drive C:\.
♦ Oracle installed on the tool.

To verify:
Check that a folder named C:\Oracle does exist (look for C:\Oracle, not
for any other name)
♦ MIL installed on the tool.
To verify:
a. Open the folder C:\BIN_COMMON.
b. Right click a MIL*.DLL file (any file of the form MIL*.DLL).
c. From the pop-up menu select: Properties > Version.
d. Verify that the version says: 7.X (for example: ).
♦ MS Windows NT with Service Pack 6a installed on the tool.
♦ A list of all new license codes for new features exists (these licenses are
obtained according to the tool’s serial number).
♦ If AIM or MPX are running with software version , you must have new
license codes, to run these features after upgrading to

(For KLASS Station prerequisites see section )

PN KLA-Tencor Confidential 1

Section 1: Introduction Deliverables

Deliverables

All required deliverables are included in the Archer Product Family Software
version kit, PN
This kit contains:
1. Archer Product Family Software version CD-ROM, PN
2. Archer Product Family Software version Installation Manual,

PN (this document).
3. Archer Product Family User Information Suite for Software version

CD-ROM, PN

Installation Team Resources

Personnel
KLA-Tencor Customer Service Engineer.
Special Tools and Consumables
None.
Required Documentation
1. Archer Product Family Software version Installation Manual,

(this document).
2. GEM Reference Manual for Archer Software version
3. RDM Installation Manual (if upgrading to RDM is required).

Reference Documentation

Your Archer system Service Manual.
Your Archer system Operation Manual.

2 KLA-Tencor Confidential Archer Installation

Section 2: Installation Procedure Reference Documentation

2. Installation Procedure

IMPORTANT

Before you start, check the KLA-Tencor Israel Intranet site
http://isrintranet/sw/ to find out if you have the latest Service Pack, or
for a later Installation procedure.

A Service Pack always includes all previous Service Packs since the last Base
version, and is composed of:

• A description of the Service Pack, including instructions for installation as
well as a list of which bugs are fixed by this Service Pack; and

• The file(s) containing the actual software.

The documents found on the Optical Metrology User Documentation page
usually describe the basic software version Installation/Upgrade (not the
Service Pack upgrade).

This document provides step-by-step instructions for upgrading the Archer
system software from version or , to software version

NOTE

The notation software version , in this document stands for software
version with or without a service pack (1, 2, or 3).

The table below provides specific references to the information required for
each installation case.

If you need to… Follow the
instructions in:

1. Upgrade Archer system software version , , ,
or software version , to software version , , 3

-Or-

Reinstall software version

2. Upgrade the RDM System

(if the Archer Tool is part of an RDM System,

then the RDM server and clients must be

upgraded to RDM software version )

3. Upgrade KLASS Station software 4

(if the Archer Tool is connected to KLASS

Station, then the KLASS Station software must

be upgraded to support software version)

IMPORTANT

For all installation procedures, log on to the system (or any related system)
with Administrator privileges.

PN KLA-Tencor Confidential 3

Section 2: Installation Procedure Upgrading RDM

Upgrading RDM

Before You Begin

Before you begin, please read the following important notes:

IMPORTANT

• RDM is an optional module.
Archer systems running Archer software version requires RDM
software version

• If the Archer tool is part of an RDM System (server and one or more
tools), the RDM server and all clients must be upgraded to RDM software
version

• If an RDM client is already installed on the Archer tool, you will have to
reinstall RDM software version on the client Archer tool, after
completing the Archer software installation.
This client must be reinstalled regardless of the previous client software
version (even if the client runs RDM software version ).

Installation

„ To install RDM , follow the instructions in your RDM Installation
Manual.

4 KLA-Tencor Confidential Archer Installation

Section 2: Installation Procedure System Backup

System Backup

CAUTION

Verify that there are no copies of any Archer system applications (such as:
Killall, MCDB, Machine, or Diag) on the Desktop. Only shortcuts are allowed.
Any copy of an Archer system application should be deleted from the Desktop
before starting the upgrade procedure.

This section provides instructions for the preparations required to install
software version

System Backup to Drive F

To backup the system to Drive F:

1. Restart the computer (ALT+CTRL+DEL).
2. When the system prompts you to select the boot drive, select the DISK

no.1 or STANDALONE (D drive) boot option.
3. Press ALT+CTRL+DEL and log on as Administrator.

(no password needed).
4. Open Windows NT Explorer.
5. On the View menu, click Show all files to open the Folder Options

dialog box.
6. Click the View tab, select Show all files (in the Hidden files group), and

click OK.
7. Empty the Recycle Bin.
8. Create a new folder in drive F and name it Backup_'Date'.

For example: Backup_15Jul
9. Copy the entire content of drive C:\ (All folders and files except the file:

C:\manicapital.com) to the backup folder you created in drive D:\. This
operation may take several minutes, depending on the total size of the
files in drive C.
When the operation is complete, proceed to section System Backup
to DAT Tape.

PN KLA-Tencor Confidential 5

Section 2: Installation Procedure System Backup

System Backup to DAT Tape

To backup the system to DAT Tape:

1. Restart the computer (ALT+CTRL+DEL).

2. When the system prompts you to select the boot drive, select the
disk No.1 or STANDALONE (D drive) boot option.

3. Press ALT+CTRL+DEL and log on as Administrator (no password needed).

4. Insert the DAT Tape into the DAT drive and wait about a minute for the
tape to be mounted (verify that the tab on the tape is in a closed position
to enable writing).

5. Open the Backup window: Start > Programs > Administrative
Tools > Backup.
The Backup window opens with two dialog boxes: Drives: and Tapes.
These dialog boxes might be minimized. Display both dialog boxes on the
screen.

6. If the DAT tape you are using contains a previous backup, erase it
(Operations > Erase tape).

7. On the Drives dialog box, select the C:drive check box and click the
C:drive icon.

8. Click Backup on the toolbar and select the following options:
Tape Name: enter a name in the box labeled Tape Name by using
machine serial number and date.
For example: Archer10 06/15/
Operation: Replace.
Select Verify After Backup.
Type in a name for the description. Enter the tape name from step (a), or
enter a name for the description.
Backup Type: Normal.
Log path: D:\WINNT\manicapital.com
Log Information: Full Detail.

9. Start the backup operation by clicking OK.
It may be necessary to use more than one tape for the backup. Remove a
tape by pressing the button on the face of the DAT drive, and insert an
additional tape.

When backup is complete, remove the tape as previously described, or by
clicking the Operations menu and selecting Eject Tape.

Move the Write Protect switch of the tape to the left to change its status
to Read Only.

From the Operations menu, select Exit to exit the backup program.

Restart the computer (ALT+CTRL+DEL).

Proceed to section Uninstalling Software Version Security Module.

6 KLA-Tencor Confidential Archer Installation

Section 2: Installation Procedure Uninstalling Software Version Security Module

Uninstalling Software Version Security Module

To uninstall the current Archer Security module:
1. Insert the Archer software CD-ROM into the CD-ROM drive.
2. Copy the folder E:\Security (E:\ = CD-ROM drive name) to C:\

The following message is displayed.

3. Click Yes to All (as many times as required).
4. Run: C:\\Security\Prepare_Uninstall_Old_manicapital.com

The following script window opens.

5. Press any key to continue.
A Killall script runs.

6. When prompted, press any key to continue.
The following message is displayed.

7. Click OK.
The script window is closed and the computer is restarted.

PN KLA-Tencor Confidential 7

Section 2: Installation Procedure Uninstalling Software Version Security Module

8. Log on as a Windows NT administrator (do not use KTADMIN as
username).

9. Run Killall (Start > Run > Killall).

Run: C:\\Security\Uninstall_Old_manicapital.com
The following script window opens.

Press any key to continue.
A Killall script runs.

When prompted, press any key to continue.
The following message is displayed.

Click OK.
The script window is closed and the computer is restarted.

Log on as a Windows NT administrator (do not use KTADMIN as
username).
Several error messages might be displayed.

Click OK on each error message box to continue with the installation
procedure.
The SnagIt application Welcome window might be displayed (this window
will be displayed every time a new user is defined).

Close the SnagIt application Welcome window, every time it opens.
Run Killall (Start > Run > Killall).
Proceed to section Archer Software Installation.

8 KLA-Tencor Confidential Archer Installation

Section 2: Installation Procedure Archer Software Installation

Archer Software Installation

To install Archer software version
1. Close all open applications. (To close Archer system applications, wait for

the tool to start running and the Kerror window to appear.
Click Start > Run, type Killall and then click OK.)
2. Insert the Archer software CD-ROM into the CD-ROM drive.
3. Run: E:\Archer SW Install\manicapital.com (E:\ = CD-ROM drive name).
The Welcome dialog box opens.

4. Click Next>.
The Software License Agreement dialog box opens.

5. Click Yes to accept the terms.

PN KLA-Tencor Confidential 9

Section 2: Installation Procedure Archer Software Installation

The Information dialog box opens, displaying the current Archer
installation status.

6. Click Next.
The following message is displayed.

7. Close any open applications, using ALT + TAB,
or using ALT + CTRL +DEL (the Windows Task Manager).

8. When all applications are closed, click OK in the message box.
The Archer system installation process starts. A progress bar shows the
progress of files being copied (this step takes a few minutes).

10 KLA-Tencor Confidential Archer Installation

Section 2: Installation Procedure Archer Software Installation

9. When the installation wizard finishes copying the installation files, there
are two options to proceed:

a. If upgrading from software version , the installation wizard
automatically installs MS Data Access Components Proceed to
step

b. If upgrading from software version , the installation wizard skips
the MS Data Access Components installation. Proceed to step

Perform this step only if upgrading from software version If
upgrading from software version , skip this step and proceed to step


When the installation wizard finishes copying and updating, MS Data
Access Components are installed.

A progress bar is shown, and then the following End User License
Agreement is displayed.

a. Select the check box to accept the agreement, and click Next.
The installation wizard checks for available disk space, and then the
following dialog box is displayed.

b. Click Next to continue.

PN KLA-Tencor Confidential 11

Section 2: Installation Procedure Archer Software Installation

NOTE
Do not restart your computer now. Restart when the Setup
Complete dialog box is displayed, in step

The following dialog box is displayed:

c. Press Finish.
d. Press Close when the MS Data Access Components setup is

complete.

The installation wizard continues with various installation tasks.
The installation tasks specified below are the most time-consuming
installation tasks.

a. The registry is updated (updating the registry may take a few
minutes).

12 KLA-Tencor Confidential Archer Installation

Section 2: Installation Procedure Archer Software Installation

b. The database is updated (updating the database may take a few
minutes, depending on the size of the database).

If upgrading from a lower version, proceed to the next step.

-Or-
If you are reinstalling version , the Context Upgrade dialog box
opens. Clear the Read Only check box, and click Go.

When the application indicates that the context upgrade has been
successfully completed, close the dialog box (with the X at the upper right

corner.)

PN KLA-Tencor Confidential 13

Section 2: Installation Procedure Archer Software Installation

When installation is complete, wait for the Setup Complete dialog box to
open.

Select Yes, to restart the computer now, and click Finish.
The computer restarts.
During the restart sequence, the Archer Logon dialog box is displayed.

Log on to the Archer system as KTADMIN.
The system begins initialization.

Run Killall immediately. Do not wait until initialization is completed.
Open the folder: E:\ViewFolderOption (E:\ = CD-ROM drive name).
In this folder, double-click manicapital.com
Proceed to section Enabling Licenses.

14 KLA-Tencor Confidential Archer Installation

Section 2: Installation Procedure Enabling Licenses

Enabling Licenses

To enable licenses:
1. From the Start menu, got to Archer > Machine Configuration.

The MCDB dialog box opens. (If a Logon window opens, log on as
KTAdmin.)
2. Click Config.
3. Click the Licensing tab.
A list of all licensed features is displayed under License Configuration.

NOTE

The list of licensed features depends on the tool type. The example below
is applicable for an Archer 10 tool.

4. Verify that the enabled licensed features list displayed on the Licensing
tab complies with the licensed features list in section of the Archer
SRN, PN (the SRN can be found on the Archer Product
Family Software Version CD-ROM, in the \\Documentation folder).

NOTE

Verify that all features marked Licensed in the SRN list, are displayed.
Features marked Yes in the SRN list are active, but not displayed.
Some previously installed licenses might not be displayed. This is due to
some licensed features being changed to default features that are part of
the basic software package.

PN KLA-Tencor Confidential 15

Section 2: Installation Procedure Enabling Licenses

5. Select the check boxes next to the features that you want to license, and
click Apply.

A dialog box is displayed.

6. Type a feature's license code in the text box, and click OK.
The dialog box is displayed again and again until you enter license codes
for all the features you have selected in step 5 above.
When you click OK for the last feature, the following message is
displayed:

7. Click OK.
8. Run Killall (click Start > Run. Type: Killall and then click OK).
9. Start the Archer system (Start > Archer > Machine).
The Archer Autorun window opens.
Proceed to section 3: Verifying the Correct Software Version.

16 KLA-Tencor Confidential Archer Installation

Section 3: Verifying the Correct Software Version Enabling Licenses

3. Verifying the Correct Software Version

To verify that the Archer software version is correct:
1. From the Autorun window, select the menu option Help > About

Archer.
Verify that the correct software version is displayed in the software
version text box (= ).

2. Click OK to close the dialog box.
3. If the system has a KLASS Station, proceed to section 4 to upgrade it.

Or-

If the system does not have a KLASS Station, proceed to
section 6: Configuring the Tool for FA.

PN KLA-Tencor Confidential 17

Section 4: Upgrading KLASS Station Software Prerequisites

4. Upgrading KLASS Station Software

NOTE
The KLASS Station is an optional module.
If the system has a KLASS Station, you must upgrade it as described in this
section.

Prerequisites

Site Prerequisites
♦ MS Windows NT with Service Pack 5 (or higher) is installed on the

KLASS Station.
♦ RS1 software version / is installed on the KLASS Station.
Deliverables
See section
Installation Team Resources
See section

Upgrade Procedure

This section provides step-by-step instructions on how to upgrade the KLASS
Station to software version

IMPORTANT
• The upgraded KLASS Station for the Archer system software version

will no longer be compliant with Archer software versions , ,
, , or
• For all installation procedures, log on to the system with Administrator
privileges.

To Upgrade the KLASS Station:
1. Insert the Archer software version CD-ROM into the CD-ROM drive of

the KLASS Station computer.
2. Run E:\ KLASSStationUpgradeForAV\manicapital.com

(E:\ = CD-ROM drive name).
Running this batch file closes all open KLASS processes, and copies the
installation files into the folder C:\Analysis\Install\.

18 KLA-Tencor Confidential Archer Installation

Section 4: Upgrading KLASS Station Software Upgrade Procedure

3. Run C:\Analysis\Install\KLASSexe file.
Follow the instructions displayed on screen.
Whenever prompted, select the default options.

4. Run C:\Analysis\Install\AnServerexe file.
Follow the instructions displayed on screen.
Whenever prompted, select the default options.

IMPORTANT
If asked whether to re-install the Read-Only file
C:\Winnit\System32\Mfcdll during the installation, choose No.

5. If the SMP Analysis package is required, run
C:\Analysis\Install\SMPFexe.
Follow the instructions displayed on screen.
Whenever prompted, select the default options.

6. If the Flier Culling package is required, run
C:\Analysis\Install\KLASSFlierCullingexe.
Follow the instructions displayed on screen.
Whenever prompted, select the default options.

NOTE

Running KLASSFlierCullingexe also installs the source code of the
filter RPL in C:\Program Files\KLASS\Work\manicapital.com
If a previous RPL by that name already exists at this folder, it should be
backed up before installation.

7. If the MPX package is required, run C:\Analysis\Install\FELMexe.
a. Follow the instructions displayed on screen.
Whenever prompted, select the default options.
b. To register the MPX license, see section Registering the MPX
License.

8. When the upgrade is finished, restart the KLASS Station computer
(ALT+CTRL+DEL).

PN KLA-Tencor Confidential 19

Section 4: Upgrading KLASS Station Software Upgrade Procedure

Registering the MPX License

IMPORTANT
Contact OMD to obtain a license key using the volume serial number obtained
in step 1, below.

To register the MPX license:
1. Obtain the eight-digit Volume Serial number of the PC:

a. From the Start menu, got to Programs > MS-DOS prompt.
A DOS prompt window opens.

b. Type dir aaa.
The Volume Serial number is displayed.

c. Record the number without the hyphen.
d. Return to Windows NT: type Exit, and then press ENTER.
2. Contact OMD to obtain a license key.
3. After obtaining the license, from the Start menu, select Programs >
KLASS for Windows > License Key Setup.
The License Key Setup dialog box is displayed.
4. In the License Key Setup dialog box, fill in Product Name,
Expiration Date and the License Key issued by OMD.
5. Press the Install key.
6. Restart the computer.

20 KLA-Tencor Confidential Archer Installation

Section 4: Upgrading KLASS Station Software Verifying Correct Installation

Verifying Correct Installation

Verifying the Installation on the KLASS Computer

To verify the installation:
1. Select: Start > RS1-KLASS for Windows.

The RS/Client Main window opens.

2. From the KLA Application Menus, select the Stepper Setup
Analysis option and press ENTER.

The Stepper Setup Analysis menu and the KLASS for Windows
software version are displayed.

3. Verify that the KLASS for Windows software version is

PN KLA-Tencor Confidential 21

Section 4: Upgrading KLASS Station Software Verifying Correct Installation

4. Quit RS1.
5. Select: Start > Start ARP.

The ARP Analysis window opens.

6. Click Upload Data Setup.
When you click this button for the first time after completing the upgrade
process, the following error message is displayed.

7. Click OK.
The Analysis Upload Data Setup dialog box opens.

22 KLA-Tencor Confidential Archer Installation

Section 4: Upgrading KLASS Station Software Verifying Correct Installation

8. Click Version.
9. Verify that the AnServer software version is , as shown below.

Click OK.
Click Apply & Exit, on the Analysis Upload Data Setup dialog box.
Repeat steps 6 to 10 for the View button on the ARP Analysis Window.
In the RS1 prompt, enter: CALLl #KLAUTInfo.
Verify that the KLAUT version is KLAUT
Proceed to section Verifying Installation on the Archer System

Computer.

PN KLA-Tencor Confidential 23

Section 4: Upgrading KLASS Station Software Verifying Installation on the Archer System Computer

Verifying Installation on the Archer System Computer

To verify the installation:
1. Verify the KLASS Station computer name is correct:

Check that the MCDB key \Analysis\KlassStationMachine, contains
the KLASS Station computer name (exact same computer name).
2. Verify the tool is configured to send data to KLASS:
Check that the MCDB key \Analysis\AnalysisType is set to KLASS
3. To verify that results are transferred to the KLASS Station, open the
Result Viewer (on the Archer system) and click Export View.
a. Select a lot on the left pane by double clicking on it.
b. Open the Destination drop down list, and select Host+Analysis+ARP.
c. Click Export to export the selected lot to the KLASS Station.
d. On the KLASS Station, verify that the ARP Analysis window pops up,

containing the KLASS results for the exported lot (as shown in the
example below).

4. When this screen is displayed, the communication between the Archer
system and the KLASS Station is verified.

5. Proceed to section 5: Configuring SnagIt to Use Tool Thermal Printer.

24 KLA-Tencor Confidential Archer Installation

Section 5: Configuring SnagIt to Use Tool Thermal Printer

5. Configuring SnagIt to Use Tool Thermal Printer

1. Open the Printers folder (Start > Settings > Printers).
2. Set the tool thermal printer (usually Sony or Mitsubishi) as the default

printer (right click the thermal printer icon and select Default).
3. Close the Printers folder.
4. Open SnagIt main window (Start > Programs > SnagIt).
5. Configure SnagIt as follows:
6. Set the thermal printer to be SnagIt default printer:

a. From SnagIt main window select: Output > Properties.
b. Select the Printer tab.
c. Verify that the Default Windows Printer option button is selected.
d. Verify that the Default Windows Printer is the tool thermal

printer.
e. Click the Page Layout button.
f. Select the Maximize Image on a Single Page option button.
g. Click OK on the Page Layout dialog box.
h. Click Apply on the Output Properties dialog box.
i. Click OK on the Output Properties dialog box, to close it.
7. Continue with configuring SnagIt according to your requirements.
8. When you finished with SnagIt configuration, close SnagIt.
9. When SnagIt is closed, turn off the tool thermal printer.
When SnagIt is closed, turn On the tool thermal printer.
Open SnagIt.
Print a screen shot using SnagIt, and verify the printout on the tool
thermal printer.
Proceed to section 6: Configuring the Tool for FA.

PN KLA-Tencor Confidential 25

Section 6: Configuring the Tool for FA

6. Configuring the Tool for FA

Perform this procedure only if the tool has a Host computer.
After upgrading the software, reconfigure the tool through the Host, with all
the required GEM Equipment Constants, report and events, and alarms.
For information on Tool configuration, see the Archer System software
Version GEM Reference manual, PN
♦ For a complete list of ECs, see section GEM Equipment Constant

Configurations.
♦ For Reports and Events, see section Host Defines Reports and Events.
♦ For Alarms, see section Enable/Disable Alarms.

CAUTION
ProcessOrderMgmt (CJ object attribute #10 and VID) has been modified
in order to align with SEMI E
This may require a corresponding modification of the Host’s SW, in case it
refers to the above when creating/managing Control Jobs.
You have completed the upgrade procedure.

26 KLA-Tencor Confidential Archer Installation

You took the software and demand to introduce the serial number and so forth to set up. Shockingly, you accidentally lose this data, and to get back up. You need to experience the hard phases of an item. Support for that software or purchase another software. Hello friends Today, in this article, you will find all the details about. In addition to Serial Box Mac 4 Software for Mac in this article. As you see below because today we have brought this software absolutely free for you. You can download it and use it inside your MacBook. You will find its download link below, along with the Serial Box Mac 4 Apple Store. Will also get you the link below where you can go to your iPhone. And together with all the Serial Box Mac 4 in the header information, you are given in this article for free.

Also Read:Skype for Mac v Free Voice and Video Calling

Download Link Below:

[email&#;protected] ( MB)

App Store Preview

Also Read:Downie v MacOS Download Movie Software from the Website

Serial box mac Software Serial Number

Revo Uninstaller Pro helps you to uninstall software and remove unwanted programs installed on your computer easily! With its advanced and fast algorithms, Revo Uninstaller analyzes an application’s data before uninstall and scans for remnants after the uninstall of a program. After the program’s regular uninstaller runs, you can remove additional unnecessary files, folders and registry keys that are usually left over on your computer. To remove a program completely and without leaving a trace you can monitor all system changes made during its installation, and then use that information to uninstall it with one click only – simple and easy! Full native bit support.

Homepage
Changelog

Download Revo Uninstaller Pro Installer

Download Revo Uninstaller Pro Portable

Revo Uninstaller Pro License & Crack

Notes:

For Installer

Copy the license file &#;manicapital.com&#; to
&#;C:\ProgramData\VS Revo Group\Revo Uninstaller Pro&#; or &#;%ALLUSERSPROFILE%\VS Revo Group\Revo Uninstaller Pro&#;

For Portable

Copy the cracks to both  x64 & x86 folders and the RevoUninstallerPro_Portable folder

Previous Fix:

Revo Uninstaller Pro v3 License Registrator & Patch

Note Before :

1. All our contents are stored only in third-party web sites, and everyone can freely downloadable. We do not using any premium websites for file hosting, all are stored in free sites
2. After downloading patch/keygen, If your anti-virus detect virus, then please disable your anti-virus during the process of registration.
3. Patches/keygens are not a virus or Trojan. Patches/keygen made by by-passing the original registration of software, so anti-virus may detect it as Trojan or virus.
4. Therefore, use patches or keygens posted on our website without any worries. All our contents are trustable as they all come from trustable sources.

Thank you