NI LabVIEW Embedded Development Module v2.0 serial key or number

Development modules are slightly larger than the breakout modules but offer access to all the FT-X device pins. The modules have a USB Mini-B connector and 0.1” pitch DIP pin for connecting the interface signals.

Modules with a part number ending XA are 0.3” wide and those ending XE are 0.6” wide.

Available modules:
UMFT201XA – FT201XQ based USB to I2C, 0.3” wide module. Additional module variant - UMFT201XA-01 (featured in UMFT201XA datasheet)
UMFT220XA – FT220XQ based USB to Enhanced 4-Bit SPI / FT1248, 0.3” wide module. Additional module variant - UMFT220XA-01 (featured in UMFT220XA datasheet)
UMFT221XA – FT221XQ based USB to Enhanced 8-Bit SPI / FT1248, 0.3” wide module. Additional module variant - UMFT221XA-01 (featured in UMFT221XA datasheet)
UMFT230XA – FT230XQ based USB to basic UART, 0.3” wide module. Additional module variant - UMFT230XA-01 (featured in UMFT230XA datasheet)
UMFT231XA – FT231XQ based USB to full handshake UART, 0.3” wide module. Additional module variant - UMFT231XA-01 (featured in UMFT231XA datasheet)
UMFT240XA – FT240XQ based USB to 8 – bit FIFO, 0.3” wide module. Additional module variant - UMFT240XA-01 (featured in UMFT240XA datasheet)

UMFT201XE – FT201XQ based USB to I2C, 0.6” wide module
UMFT221XE – FT221XQ based USB to Enhanced 8-Bit SPI / FT1248, 0.6” wide module
UMFT231XE – FT231XQ based USB to full handshake UART, 0.6” wide module
UMFT234XF – FT234XD based USB to basic UART module
UMFT240XE – FT240XQ based USB to 8 – bit FIFO, 0.6” wide module

Featuring the new FT232H, this module provides an engineer with an easy way to integrate the FT232H into a proof-of-concept design, or quickly modify an existing product. Using the on-board EEPROM, these capabilities include the ability to configure the FT232H as either a serial data transfer interface (JTAG/SPI/I2C/UART - as well as the new FT1248 protocol) or parallel FIFO interface, at speeds up to 40MByte/s. Built to conform to a standard 0.6” 28 pin DIP socket, this module can be either self or bus-powered, with a robust 3.3V IO structure that can directly interface to 5V logic without buffers. Using FTDI’s world class drivers, an engineer can easily establish USB communication to the FT232H using either virtual com port or D2XX royalty-free software.

The FT121 G-Sensor shield is designed to connect directly to an Arduino Pro development board. The shield allows the micro-controller on the Arduino Pro to access the FT121 USB device controller.Using the FTDI FT121 chipset and a three axes linear accelerometer (ST LIS331DLH) device, the module may be used to implement a USB HID game controller. The user may also define other interesting applications from the micro-controller board.

The Arduino Pro is a micro-controller board based on the ATmega168 or ATmega328 and is not available from FTDI.

Vinco is a cost effective Vinculum-II (VNC2) development platform inspired by Arduino. The Vinco is a dual channel USB Host/Device Controller is targeted at rapid development and prototyping of USB Host/Device interfaces. Vinco is a superset of the Arduino Duemilanove / Uno with 2 extra rows of headers providing an extra 10 pins and can be programmed using a subset of standard ANSII ‘C’ using the FTDI free of charge software development environment, consisting of development tools, software drivers and libraries. An optional Vinco prototyping board provides add-on expansion board support. The Vinco features an 8-channel, 10Bit ADC, PWM interface and supports connectivity to a wide range of application boards developed by the Arduino open-source community. These include Ethernet, motor control, LCD and many others applications.

Note that a debugger/programmer module is required to program the Vinco.

Vinco Shield is a prototyping board for interfacing additional custom circuitry to the Vinco motherboard. In addition to bringing out all connections of the Vinco motherboard, there are three undedicated LEDs and two switches (one dedicated to Reset).

Please see section 10 (page 17) of the Vinco data sheet http://www.ftdichip.com/Support/Documents/DataSheets/Modules/DS_Vinco.pdf for more information. Part number VNCLO-SHLD-1A

The FT4232H USB serial/hub module was designed to connect to FTDI’s V2DIPx modules, as well as any USB Host interface (e.g. PC) to expand the number of interfaces that can be accessed downstream from a Host. The module has an FTDI FT4232H USB 2.0 Hi-Speed to UART/MPSSE chip which supports data rates of 40Mb/s and takes care of all USB signaling and protocols. It also features a GL850G USB 2.0 hub controller chip, the functions of which can be customized.

The Morph-IC-II is a USB based FPGA development module featuring the Altera Cyclone-II FPGA with the FTDI FT2232H USB to UART/FIFO/MPSSE converter IC.  The module provides integration of Hi-Speed USB capability (480Mbit/s) with an FPGA, to enable ultra-fast software based FPGA configuration/reconfiguration and communication using the FTDI royalty free drivers.

The concept of the Morph-IC-II is to provide the ability to easily alter the function and capability of a silicon device via software, allowing multiple functions to be implemented within the same silicon, whilst reducing bill of materials and silicon cost. Features include:

• Powerful silicon development platform.  Software re-configurability allows users to support multiple functions within a single silicon platform.
• High performance, low power Altera Cyclone-II EP2C5F256C8N FPGA device.
  • 4,608 embedded FPGA Logic Elements (about 80,000 Gates typically).
  • 26 M4K RAM blocks (119Kbits), 13 embedded multipliers and Nios II embedded processor support.
• USB 2.0 Hi-speed (480Mbits/s) connection via FT2232H USB to dual channel UART/FIFO/MPSSE IC
  • Supports FPGA-PC USB Data transfers at up to 40MBytes/s.
  • Supports ultra-fast software based configuration/reconfiguration of FPGA (less than 100ms).
• Range of flexible for FPGA communication interfaces, including FIFO interface, and MPSSE configurable serial controller interface providing support for SPI and I2C and other serial protocols.
• Compact module features up to 124 x 0.1” pitch headers providing access to 96 I/Os on the FPGA and FT2232H module.
• Onboard USB type B connector provides connection to a PC, supporting software communication via FTDI VCP and D2XX API drivers.  The D2XX API supports communication via C/C++ as well as other software languages.
• Onboard JTAG port connector for FPGA boundary scan, test and configuration.  JTAG interface also accessible via module header pins.
• Module is supplied with VHDL reference designs, software samples and utilities. FPGA programming supported by free Quartus II Web Edition Software from Altera.

  .

Target Applications
Wide range of VLSI logic circuit design applications including ASIC prototyping, FPGA design for glue-logic or IP development.  The wide range resources including FPGA reference designs, software utilities and samples also makes the module ideal as a low-cost educational platform.

The FT2232H Mini Module is a USB to dual channel serial/MPSSE/FIFO interface converter module based on the FT2232H USB Hi-Speed IC. The FT2232H handles all the USB signalling and protocol handling. The module provides access to device I/O interfaces via 2 double row 0.1" pitch male connectors.  The module is ideal for development purposes to quickly prove functionality of adding USB to a target design.

The FT4232H Mini Module is a USB-to-serial/MPSSE interface converter module based on the FT4232H IC. The FT4232H bridge chip supports USB Hi-Speed transfers and handles all the USB protocol. The development module provides access to the quad channel serial / MPSSE converter interfaces via a set of 2 double row 0.1" pitch male connectors.  It is ideal for development purposes to quickly prove functionality of adding USB to a target design.